ATX24-Pin POwer Connector: JPWR1

This connector allows you to connect and ATX 24-Pin power supply.  To connect the ATX24-pin power supply, make sure the plug of the power supply is inserted in the proper orientation and the pins are aligned.  Then push down the power supply firmly into the connector.


ATX 4-Pin Power Connector:JPWR2
This 12V power connector is used to provide power to the CPU.

___________________________________

Installing Memory Modules

01. The memory module has only one notch on the center and will only fit in the right orientation.


02. Insert the memory module vertically in to the DIMM slot.  Then push it in until the golden finger on the memory module is deeply inserted in the DIMM slot.  You can barely see the golden finger if the memory module is properly inserted in the DIMM slot.


03. The plastic clip at each side of the DIMM slot will automatically close.

MEMORY MODULES

IMPORTANT


01. DDR2 memory dodules are not interchangeable with DDR and the DDR2 standard is not backwards compatible.  You should always install DDR2 memory modules in the DDR2 DIMM slots.


02.In Dual-Channel mode, make sure that you install memory modules of the same type and density in different channel DIMM slots.


03.To enable successful system boot-up, always insert the memory modules into the DIMM1 first.

Processor fitting

01. Pull liver side way away form the socket.  Make sure to rise the live up to a 90 degrees angle.

02. Look for the gold arrow of the CPU.  The gold arrow should point as shown in the picture.  The CPU can only fit in the correct orientation.

03. If the CPU is correctly installed, the pins should be completely embedded into the socket and can not be seen.  Please note that any violation of the correct installation procedures may cause permanent damages to your main-board.

04. Press the CPU down firmly into the socket and close the lever.  As the CPU is likely to move while the lever is being closed, always close the lever with your fingers pressing tightly on top of the CPU to make sure the CPU is properly and completely embedded into the socket.

05. Position the cooling set onto the retention mechanism.  Hook one end of the clip to hook first.

06. Then press down the other end of the clip to fasten the cooling set on the top of the retention mechanism.    Locate the Fix lever and lift up it.

07. Fasten down the lever.

08. Attach the CPU fan cable to the CPU fan connector on the main-board.

PROCESSOR FITTING

Rear panel

REAR PANEL


The rear panel provides the following connectors:

REAR PANEL

HARDWARE SETUP


This chapter provides you with the information about hardware setup procedures. While doing the installation, be careful in holding the components and follow the installation procedures.  For some components, if you install in the wrong orientation, the components will not work properly.  Use a grounded wrist strap before handling computer components.  Static electricity may damage the components.


CPU& Cooler installation for AM2/ AM2+/ AM3


When  you are installing the CPU, make sure the CPU has a cooler attached on the top to prevent overheating.  Meanwhile, do not forget to apply some thermal paste on CPU before installing the heat sink/cooler fan for better heat dispersion.


Follow the steps below to install the CPU & cooler correctly.  Wrong installation will cause the damage of your CPU & main board. 

K9N6PGM2-V2 mother board user guide

GETTING START

K9N6PGM2-V2

Thank you for choosing the K9N6PGM2-V2 series (MS-7309 v2.x) Micro-ATX mainboard.  The K9N6PGM2-V2 series are design based on NVIDIA GeForce 6150SE & nForce 430 chipset for optional system effciency.  Designed to fit the advanced AmD AM2/AM2+AM3 processor, the K9N6PGM2-V2 series deliver a high performance and professional desktop platform solution

SPECIFICATIONS

01.Supports AMD Sempron, Atholon 64 and Athlon 64x2 processors in the AM2/ AM2+ package, and supports AMD Phenom II/Athlon II processor in the AM3 package


02. Supports 95W processor only.


Hyper Transport
01. HyperTransport 1.0


Chipset
01.NVIDIA GeForce 6150SE & nForce 430 chipset


Memory Supports
01.DDR2 800/ 667 SDRAM (total Max. 8GB)
02.2 DDR2 DIMMs (240pin/ 1.8V)


Lan
01.Supports 10/100/1000 LAN by Realtek RTL8211cl
02.Or supports 10/100 LAN by realtek RTL8201EL


1394(Optional)
01.Chip integrated by VIA VT6315N


Audio
01.Chip integrated by Realtek ALC888/ ALC888S
02.Supports 7.1 channels audio out (by 6 audio-jacks)
03.Compliant with Azlia 1.0 Spec


Ide
01.1 Ide port
02.Supports Ultra DMA 66/100/133, PIO & Bus Master operation mode


Sata
01.SATA1-4 support RAID 0/ 1/15/ 0+1
02.Supports storage and data transfers at up to 3.0 Gb/s


Floppy
01.1 floppy port
02.Supports 1 FDD with 360 KB, 720 KB, 1.2MB, 1.44 MB and 2.88 MB


Connectors
Back Pannel
1 PS/2 mouse port
1 PS/2 keyboard port
1 Serial port
1 VGA port
1 1394 port (optional)
1 LAN jack
4 USB 2.0 Ports
3/6 (optional) flexible audio jacks
On-Board Connectors
2 USB 2.0 connectors
1 Parallel port connector
1 IEEE 1394 connector (optional)
1 SPDIF-Out connector
1 Front Pannel Audio connector
1 CD-in connector
1 TPM connector (optional)
1 Chassis intrusion connector
1Overclock FSB switch (optional)


Slots
01.1 PCI Express 1.0x16 slot
02.1 PCI Express 1.0x1 slot
03.2 PCI slots, support 3.3V/5V PCI bus interface


Form factor
01. Micto-ATX (24.4cm x 20.0 cm)


Mounting
01.6mounting holes